Anyplace top buy Star Board in Tallahassee, just need small scrap piece to glue to the inside of my console to mount a fuse block to...
RF
Star Board
Moderators: bman, Chalk, Tom Keels
-
Jumptrout51
- Site Sponsor
- Posts: 12120
- Joined: December 12th, 2001, 8:00 pm
- Location: Tallahassee
Re: Star Board
Well - Boaters World has it but it must be made of gold (or oil) for what they want for a 12 x 24 piece....
I need to mount the fuse block on the console wall, but the block is made for the bolts to go behind it, and if I do that the bolt heads will be under the rod holders on the outside... any ideas on mounting? maybe Gorilla Glue the whole block to the inside, but i hate not being able to remove it if ever needed....
I need to mount the fuse block on the console wall, but the block is made for the bolts to go behind it, and if I do that the bolt heads will be under the rod holders on the outside... any ideas on mounting? maybe Gorilla Glue the whole block to the inside, but i hate not being able to remove it if ever needed....
-
Barhopr
- Site Sponsor
- Posts: 3736
- Joined: September 25th, 2006, 10:21 pm
- Location: Bainbridge/Beacon Hill
Re: Star Board
go to someplace like tallahassee marine...maybe they have a scrap piece laying around from rigging a boat.
I think they also have some smaller pieces at West Marine
I think they also have some smaller pieces at West Marine
VIVA la BT
_______________
_______________-
Jumptrout51
- Site Sponsor
- Posts: 12120
- Joined: December 12th, 2001, 8:00 pm
- Location: Tallahassee
Re: Star Board
Barhopr is right. Tallahassee Marine probably has a small piece they could help you with.
WHOSE FISH IS IT?
Re: Star Board
corroded fuse on the GPS went out last time after catching bait for 1 1/2 hours and fillin the well, not fun tracking down the culprit, time to rewire!
-
Reel Cowboy
- Site Sponsor
- Posts: 5552
- Joined: September 22nd, 2006, 10:45 am
- Location: Dallas, Tx
- Contact:
Re: Star Board
That's where I've gotten mine from or just about any boat place that does any rigging.Barhopr wrote:go to someplace like tallahassee marine...maybe they have a scrap piece laying around from rigging a boat.
I think they also have some smaller pieces at West Marine
In the words of the great Doc Holliday, "I'll be your huckleberry"
-
What a mess
- Posts: 1569
- Joined: October 2nd, 2006, 8:35 pm
- Location: Valdosta Ga.
Re: Star Board
Would a cutting board from wal mart or lowes work?
Yesterday it was taboo today it is normal what the heck will they be doing tomorrow?
Re: Star Board
Yes. This panel is made from a piece of cutting board.What a mess wrote:Would a cutting board from wal mart or lowes work?
Redfin, if you don't want to use a piece of cutting board and can't find a piece of starboard, let me know. I have a few scraps.
What was I supposed to do today?
-
What a mess
- Posts: 1569
- Joined: October 2nd, 2006, 8:35 pm
- Location: Valdosta Ga.
Re: Star Board
The largest cutting board I have seen was either lowes or home depot can't remember which.
Great minds think alike.
Also the wackiest too!
Great minds think alike.
Also the wackiest too!
Yesterday it was taboo today it is normal what the heck will they be doing tomorrow?
Re: Star Board
Brown's Kitchen Supply, on Capital Circle NE, has larger size cutting boards. The piece in the picture is less than half the board I bought.
What was I supposed to do today?
-
BAD BEHAVIOR
- Site Sponsor
- Posts: 2516
- Joined: April 25th, 2007, 11:08 pm
- Location: adel/cairo, ga
Re: Star Board
Ive got some scraps left over from the Maverick. Shoot me a pm if you still need some. Be glad to mail you a piece!
Be glad to mail you a piece!A wise person pays attention to correction that will improve his life...... Proverbs 15:31 ICB <")))))>*<
TEAM BAD BEHAVIOR
TEAM BAD BEHAVIOR