All things having to do with boats, trailers, engines, electronics and accessories.
Moderators: bman , Chalk , Tom Keels
tin can
Site Sponsor
Posts: 12535 Joined: May 6th, 2002, 8:00 pmLocation: Tallahassee, Florida
Post
by tin can February 24th, 2005, 11:00 am
What was I supposed to do today?
wevans
Site Sponsor
Posts: 12827 Joined: June 12th, 2002, 11:06 amLocation: Sopchoppy
Post
by wevans February 24th, 2005, 11:11 am
“Before you criticize someone, you should walk a mile in their shoes. That way when you criticize them, you are a mile away from them and you have their shoes.”
tin can
Site Sponsor
Posts: 12535 Joined: May 6th, 2002, 8:00 pmLocation: Tallahassee, Florida
Post
by tin can February 24th, 2005, 11:13 am
The hole is on the inside. No holes in the hull.
What was I supposed to do today?
wevans
Site Sponsor
Posts: 12827 Joined: June 12th, 2002, 11:06 amLocation: Sopchoppy
Post
by wevans February 24th, 2005, 11:14 am
Give him time TC, give him time
“Before you criticize someone, you should walk a mile in their shoes. That way when you criticize them, you are a mile away from them and you have their shoes.”
Chalk
Moderator
Posts: 11996 Joined: March 9th, 2002, 8:00 pmLocation: 30° 13' N, 85° 40' W
Contact:
Post
by Chalk February 24th, 2005, 11:15 am
How much deadrise?
tin can
Site Sponsor
Posts: 12535 Joined: May 6th, 2002, 8:00 pmLocation: Tallahassee, Florida
Post
by tin can February 24th, 2005, 11:16 am
Progressive deadrise, with a pad.
What was I supposed to do today?
Chalk
Moderator
Posts: 11996 Joined: March 9th, 2002, 8:00 pmLocation: 30° 13' N, 85° 40' W
Contact:
Post
by Chalk February 24th, 2005, 11:18 am
tin can wrote: Progressive deadrise, with a pad.
Give me a visual....
tin can
Site Sponsor
Posts: 12535 Joined: May 6th, 2002, 8:00 pmLocation: Tallahassee, Florida
Post
by tin can February 24th, 2005, 11:39 am
The beam is 84" at the widest point.
Deadrise, from the center out:
concave pad 10" wide +/-
2" wide flat step
10" wide +/- rise approx. 16 degrees
2" flat step
10" wide +/- rise approx. 16 degrees
2" flat step
12" wide +/- rise approx. 6 degrees
Chine
What was I supposed to do today?
Chalk
Moderator
Posts: 11996 Joined: March 9th, 2002, 8:00 pmLocation: 30° 13' N, 85° 40' W
Contact:
Post
by Chalk February 24th, 2005, 11:46 am
It's scary when he can't go outside and take a picture
16 degrees
tin can
Site Sponsor
Posts: 12535 Joined: May 6th, 2002, 8:00 pmLocation: Tallahassee, Florida
Post
by tin can February 24th, 2005, 11:49 am
I attempted that. I can't get far enough behind the goat to get the bottom, it's too close to the ground, it's sitting on a trailer with 2 flat 6" wide bunks on each side.
What was I supposed to do today?
tin can
Site Sponsor
Posts: 12535 Joined: May 6th, 2002, 8:00 pmLocation: Tallahassee, Florida
Post
by tin can February 24th, 2005, 12:00 pm
What was I supposed to do today?
Sir reel
Site Sponsor
Posts: 6206 Joined: January 22nd, 2003, 11:35 amLocation: Tallahassee
Post
by Sir reel February 24th, 2005, 12:10 pm
What may be confusing Chalk.... is the fact that the trailer still has it's fenders on.
They ain't been knocked off yet
"Good Judgement" comes from experience, ... and a lot of that..... results from "Bad Judgement".
tin can
Site Sponsor
Posts: 12535 Joined: May 6th, 2002, 8:00 pmLocation: Tallahassee, Florida
Post
by tin can February 24th, 2005, 1:37 pm
As Wevans said......Give him time.
What was I supposed to do today?
tin can
Site Sponsor
Posts: 12535 Joined: May 6th, 2002, 8:00 pmLocation: Tallahassee, Florida
Post
by tin can February 24th, 2005, 11:23 pm
This is what's on the back of Chalk's project......
And he ain't gettin it.
What was I supposed to do today?
A little wax and she will be good as new.....I don't think it will be ready for Keaton 
They ain't been knocked off yet 