Page 1 of 2
Comprops
Posted: April 29th, 2007, 9:09 am
by Redbelly
These look interesting. Does anyone know about their performance? They look like a prop for rocky areas.
They are cheap in price too.
Posted: April 29th, 2007, 9:13 am
by birddog
I think a compprop will disintegrate if you hit a rock.
Posted: April 29th, 2007, 9:54 am
by Redbelly
That's the idea. No resulting gearcase damage.
I fish Aucilla a lot. I hit rocks almost every trip, but I have been running a tiller steered boat, and no lock-down. I also idle most everywhere in the shallows.
Now I am running a fixed position motor, and see a need to be equipped for the area.
From reading about the comprops, they look very enticing...and not a wallet buster if I choose to experiment. I am going to try one before anything else.

Posted: April 29th, 2007, 12:15 pm
by birddog
You might better take a 6 pack of compprops.

Posted: April 29th, 2007, 12:27 pm
by Redbelly
birddog wrote:You might better take a 6 pack of compprops.

Now that's funny right there.....I don't care who you are!!
From their site the claim is it takes a high speed hit to shatter the prop, but low speed impact it holds together better than aluminum.
Less than $100...

I waste more than that eating out in a month.
Posted: April 29th, 2007, 12:53 pm
by birddog
Posted: April 30th, 2007, 5:15 pm
by go devil
FWIW.....I put a comp prop on a 16 ft G3 with a 30 yamaha. Got tired of the nicks it was receiving at Aucilla.
Well the good news is it saved me some nicks. The bad news is it only lasted about 3 fishing trips and was down to one blade.
I don't know if its worth it or not as the primary prop, but it makes a heck of an inexpensive backup prop.
Posted: April 30th, 2007, 5:19 pm
by go devil
double post
Posted: April 30th, 2007, 5:35 pm
by Redbelly
Thanks for the experienced reply. I suppose I'll experiment with an aluminum 4 blade.
Posted: May 3rd, 2007, 2:07 pm
by Seachaser
I run one right now. Cheaper than aluminum and tougher. Plus you can get a four blade for about 85 bucks.
Posted: May 3rd, 2007, 2:48 pm
by Chalk
I know of one person that ran one for awhile, it came apart on him offshore and he didn't have a spare...He doesn't recommend them, though he said an RPM gauge was required equipment

Posted: May 3rd, 2007, 7:06 pm
by Redbelly
Chalk wrote:, though he said an RPM gauge was required equipment


Soon to be standard equipment on the attack vessel!
Posted: May 3rd, 2007, 7:07 pm
by Redbelly
Seachaser wrote:I run one right now. Cheaper than aluminum and tougher. Plus you can get a four blade for about 85 bucks.
Is this on a tunnel hull?
Posted: May 4th, 2007, 8:24 am
by Seachaser
No, but since I added a jack plate it will scoot. It is a cheap prop and I am using mine to determine the correct pitch and as an experiment.
Posted: May 4th, 2007, 3:53 pm
by grim reeler
I think this is an appropriate time for the phrase..."you get what you pay for..."
Its probably cheaper to keep your current prop and buy insurance.
Tunnel hulls dont make you bullet proof. You only have to look at my prop and skeg for that. Even with a tunnel hull, caution is recommended in rocky areas.