Skattle Rake

The place to discuss the finer points of fly fishing.

Moderators: bman, Chalk, Tom Keels

Post Reply
User avatar
Chalk
Moderator
Posts: 11996
Joined: March 9th, 2002, 8:00 pm
Location: 30° 13' N, 85° 40' W
Contact:

Skattle Rake

Post by Chalk »

Image

I took the Borski skunk and the Capt. Bowdish's rattle snake and made this lil cocktail.

The rabbit tail is only the length of the hook and I put some marabou and Metz Deadly Dazzle (craft fur and flash mixed) under the tail to support it.

I bought all the materials from http://www.bearsden.com

Materials Used
Hook: Mustad 34007 size 2
Thread: Flat waxed nylon - color dependent (GPS preferred for spinning hair, but use what you have)
Tail: Black marabou, Metz Deadly Dazzle in Misty Black, black rabbit strip - all the length of the hook and a small hourglass rattle
Body: 2 Schlappen feathers in black, Purple and black deer hair
Weed Guard: 30-pound mono - optional


Tying:
Start the black thread at the bend of the hook and wrap enough for a base for the rattle. I place the rattle below the center line of the hook shaft.
Put a drop of superglue on the rattle once in place.
Wrap a small tuff of black marabou on top of the rattle, length of the hook.
Wrap Metz Deadly Dazzle under the rattle on both sides.
I figure eight some wraps over the Metz and marabou to pull it together around the rattle. Also loop some wraps underneath the Metz to hold it up.
Add a hooks length of black rabbit strip in front of the rattle.
Add some superglue.
Tie in the two Schlappen feathers and palmer forward and tie off.
Tie in a hank of purple deer hair - you want the tips to be just short of the Schlappen combed back. Spin it to the bottom of the hook
Place a hank of black deer hair on top of the purple deer hair - hold it in place and wrap. Should have a black top and purple bottom
Do the same thing again, but the hair should be centered and the tips cut off to make a body.
Depending on how much of a hank you get - this may be enough...if it seems short add another hank (a half hank will usually do) on bottom and top.
Whip finish and superglue
Trim it like a toad - triangle head that is tapered on top and bottom. Keep the head boxy to push water.

Spinning hair is the hardest part of this fly and trimming it. I usually use scissors to trim...a razor is quicker, also quicker to screw it up or cut you.

A video on spinning hair will help you tie this fly

http://www.youtube.com/watch?v=iQ7mqcjIT9Y[/video]
flflyfisher
Posts: 11
Joined: January 2nd, 2009, 11:31 am

Re: Skattle Rake

Post by flflyfisher »

Beautiful fly. Does it ride with the hook up?
User avatar
Chalk
Moderator
Posts: 11996
Joined: March 9th, 2002, 8:00 pm
Location: 30° 13' N, 85° 40' W
Contact:

Re: Skattle Rake

Post by Chalk »

No....hook down
User avatar
noleflyfisher
Site Sponsor
Posts: 736
Joined: April 17th, 2005, 7:20 pm

Re: Skattle Rake

Post by noleflyfisher »

Great fly Chalk. That will look juicy in the water. :thumbup:
Jumptrout51
Site Sponsor
Posts: 12120
Joined: December 12th, 2001, 8:00 pm
Location: Tallahassee

Re: Skattle Rake

Post by Jumptrout51 »

PPPpppFFFfffTTTttt!!!
WHOSE FISH IS IT?
Ashowalter
Posts: 14
Joined: February 9th, 2009, 8:42 pm

Re: Skattle Rake

Post by Ashowalter »

great video, thanks for that chalk. wrapping flies is definately an art i will someday get into. very cool.
User avatar
Barhopr
Site Sponsor
Posts: 3736
Joined: September 25th, 2006, 10:21 pm
Location: Bainbridge/Beacon Hill

Re: Skattle Rake

Post by Barhopr »

nice Chalk
VIVA la BT

Image_______________Image
User avatar
Flanders
Site Sponsor
Posts: 1037
Joined: January 20th, 2009, 5:24 pm
Location: Moultrie, Ga.

Re: Skattle Rake

Post by Flanders »

Nice!! Another post from Chalk reminding me just how much I suck at tying flys again. :bang_1 :bang_1 Great. Thanks!!! :smt098
I come from a small drinking community with a fishing problem
Post Reply