Evinrude stuck in forward

All things having to do with boats, trailers, engines, electronics and accessories.
Image

Moderators: bman, Chalk, Tom Keels

Post Reply
User avatar
flatpicker
Site Sponsor
Posts: 339
Joined: December 13th, 2006, 9:58 am
Location: Thomasville, GA

Evinrude stuck in forward

Post by flatpicker »

Anybody have any idea what would cause my motor gear shift to be stuck in forward. Our local outboard mechanic had surgery, and will be out for another two weeks, and I want to go fishing :evil: . It's a early 80's model.
A bowl of oatmeal tried to stare me down, and won!
FHC
Site Sponsor
Posts: 418
Joined: January 25th, 2009, 5:44 pm
Location: Moultrie, Ga.

Re: Evinrude stuck in forward

Post by FHC »

do not go down a 1 way street
Sea Fox
Site Sponsor
Posts: 1474
Joined: January 13th, 2003, 4:37 pm

Re: Evinrude stuck in forward

Post by Sea Fox »

Make sure your shift cable is not froze up, is the linkage moveing with throttle lever?
Sea Ya !
User avatar
flatpicker
Site Sponsor
Posts: 339
Joined: December 13th, 2006, 9:58 am
Location: Thomasville, GA

Re: Evinrude stuck in forward

Post by flatpicker »

FHC wrote:do not go down a 1 way street
Good point! :-D
Sea Fox wrote:Make sure your shift cable is not froze up, is the linkage moveing with throttle lever?
tiller steering
A bowl of oatmeal tried to stare me down, and won!
Sea Fox
Site Sponsor
Posts: 1474
Joined: January 13th, 2003, 4:37 pm

Re: Evinrude stuck in forward

Post by Sea Fox »

Drop the foot oil and see what it looks like. I would still look at the linkage good and make sure a pivot point hasent froze up
Sea Ya !
FUTCHCAIRO
Posts: 6065
Joined: December 26th, 2004, 2:36 pm
Location: CAIRO,GA

Re: Evinrude stuck in forward

Post by FUTCHCAIRO »

ON THE RIGHT SIDE OF THE SHAFT GOING TO THE GEARS IN THE FOOT THERE IS A SMALL PLATE, ABOUT1 1/4" BY 2 1/2# WITH 2 SCREWS HOLDING THE PLATE ON THE SHAFT. TAKE THE PLATE OFF AND LOOK INSIDE, THERE IS ANOTHER BRACKET , BRASS, WITH 2 3/8" BOLTS, SEE IF EITHER OF THOSE BOLTS ARE TIGHT, IF THEY ARE WILL HAVE TO GO ANOTHER ROUTE. IF THEY ARE LOOSE, TURN THE PROP A LITTLE AT A TIME WHILE LOOKING AT THE BRACKET, IF THE SOLID 3/16 TH " ROD DROPS DOWN OR UP TIGHTEN THE BOLTS AND THEN CHECK IF IT WILL COME OUT OF GEAR, I BELIEVE ON THOSE OLDER MODELS THEY HAVE SEVERAL GREASE FITTINNGS ON THE TILLER SHAFT THAT NEED GREASED AT LEAST 2 TIMES A YEAR OR WHEN THE SHAFT STARTS GETTING HARD TO TURN. IT COOULD ALSO BE THE DOG GEAR IN THE FOOT ASSEMBLY. CHECK THE OIL IN THE FOOT IF IT IS MILKY YA NEED TO DO A FOOT ASSSEMBLY WITH NEW BEARINGS ,SHIMMS , GASKET SET, AND O RINGS ON THE SHAFT. IT IS NOT THAT HARD TO DO IF YOU HAVE A REPAIR MANUEL, JUST BE SURE EVERYTHING GOES BACK IN THE SAME WAY IT CAME OUT.
PA THE OLD MAN OF THE SEA :smt006 :smt006
FUTCHCAIRO
Post Reply